One Consist Network with One ETB Node HowTo
This document describes how to configure a consist with one consist network managed by one ETBN. The consist is depicted in Figure 1.
The result of the inauguration will be a network where ETBN1 has the ETBN ID 1, the IP-address 10.128.0.1 (based on the ETBN ID and since the network is configured as TCMS). CN1 will attain the network IP 10.128.64.0/18.
.------------.
/ cst1 \
'--------------'
.-------.
--+ +-- dir1 = (ethX5, ethX6)
<-dir1| ETBN1 |dir2-> dir2 = (ethX7, ethX8)
--+ +--
'---+---'
|
-------+----- CN1 vlan10 (ethX3)
Figure 1: A consist with one consist network managed by one ETB node.
Configuration
etbn1:#> configure
etbn1:/config/#> vlan 10
Creating new VLAN vid:10 with name: vlan10
etbn1:/config/vlan-10/#> untagged ethX3
etbn1:/config/vlan-10/#> end
etbn1:/config/#> iface vlan10
etbn1:/config/iface-vlan10/#> no inet
etbn1:/config/iface-vlan10/#> inet static 10.0.0.1/18
etbn1:/config/iface-vlan10/inet-static-10.0.0.1/#> end
etbn1:/config/iface-vlan10/#> end
etbn1:/config/#> ttdp
Activating TTDP with default settings.
etbn1:/config/ttdp/#> uuid 11111111-1111-1111-1111-111111111111
etbn1:/config/ttdp/#> node 1 ecn 1
etbn1:/config/ttdp/#> ecn 1 vlan10
etbn1:/config/ttdp/#> dir1 ethX5,ethX6
Remember to manually set mdi/mdi-x mode
in port settings for all agg ports.
etbn1:/config/ttdp/#> dir2 ethX7,ethX8
Remember to manually set mdi/mdi-x mode
in port settings for all agg ports.
etbn1:/config/ttdp/#> local-id 1
etbn1:/config/ttdp/#> end
TTDP: Created VLAN 492. Note that this VLAN will not be deleted automatically
if TTDP is deactivated.
etbn1:/config/#> vlan 2
Creating new VLAN vid:2 with name: vlan2
etbn1:/config/vlan-2/#> no multicast-snooping
etbn1:/config/vlan-2/#> untagged lag-dir1,lag-dir2
etbn1:/config/vlan-2/#> end
Continue by configuring the ports.
etbn1:/config/#> port ethX5
etbn1:/config/port-ethX5/#> speed-duplex 100-full
etbn1:/config/port-ethX5/#> no auto-negotiate
etbn1:/config/port-ethX5/#> fastlink
etbn1:/config/port-ethX5/#> mdix-mode mdi
etbn1:/config/port-ethX5/#> end
etbn1:/config/#> port ethX6
etbn1:/config/port-ethX6/#> speed-duplex 100-full
etbn1:/config/port-ethX6/#> no auto-negotiate
etbn1:/config/port-ethX6/#> fastlink
etbn1:/config/port-ethX6/#> mdix-mode mdi
etbn1:/config/port-ethX6/#> end
etbn1:/config/#> port ethX7
etbn1:/config/port-ethX7/#> speed-duplex 100-full
etbn1:/config/port-ethX7/#> no auto-negotiate
etbn1:/config/port-ethX7/#> fastlink
etbn1:/config/port-ethX7/#> mdix-mode mdi
etbn1:/config/port-ethX7/#> end
etbn1:/config/#> port ethX8
etbn1:/config/port-ethX8/#> speed-duplex 100-full
etbn1:/config/port-ethX8/#> no auto-negotiate
etbn1:/config/port-ethX8/#> fastlink
etbn1:/config/port-ethX8/#> mdix-mode mdi
etbn1:/config/port-ethX8/#> end
etbn1:/config/#> end
Applying configuration.
Configuration activated.
Remember "copy run start" to save to flash (NVRAM).
etbn1:/#>
In this HowTo, it is assumed that the ETB uses crossover cabling. For this reason, all ETB ports on both ETBNs use the same MDI-X mode. If non-crossover cabling is used, these settings must be changed for two of the inward-facing ETB ports.
Inauguration Result
Using the show ttdp command we now verify that we have recevied the intended network configuration.
Highlighted in yellow are the values that are of interest.
etbn1:/#> show ttdp
TTDP NODE
backbone-id : 0 (tcms)
etbn-id : 1
etbn-ip : 10.128.0.1
local-id : 1
own-mac : 0c:65:8c:93:00:00
uuid : 11111111-1111-1111-1111-111111111111
connTableCnt : 0x32752ae8
EtbTopoCnt : 0x80ea82ac
Inauguration : INAUGURATED
Inhibition : Self: Off, Others: Off, Train: Off
CST-NET IFACE IP CONNECTED ETBNs
1 vlan10 10.0.0.1/18 1
NODE ID MAC ADDRESS ORIENTATION
1 0c:65:8c:93:00:00 Direct
CONSIST NODES DIRECTION NETWORKS
11111111-1111-1111-1111-111111111111 1 Direct 10.128.64.0/18
etbn1:/#>